Linked Body not showing up in Exploded view
Hello, I am using NX 10 to create an assembly model consisting of various sub-assemblies. On this top-level model, I am using the Wave linker to promote a body of a subassembly in order to add some...
View ArticleClik here to view.
NX11 How do I extrude out the body such that only the inner features are left?
Hey guys, how do I extrude or go about doing it for a block that has features in it (pipes etc) such that at the end of the day, there will only be those inner features left?Cheers!
View ArticleClik here to view.
extend a 3d spline to be perpendicular to a plane
I need to extend a 3d spline to be perpendicular to X-Z plane. I know Trim Curve can be used for extending. But I can't find options to set continuity at the plane. Could you kindly give some clues?...
View ArticleClik here to view.
(Part 2) Suggestions on the current design (Swept Volume)
My old post: CLICK HERE Greetings everyone! I'm following this new method & trying to get my design done. This includes the use of Swept Volume command.I'll highlight the steps below, just so that...
View ArticleExtract unlinked geometry in an assembly
Hi community, Does anybody know if it is possible to extract the geometry of the components in an assembly when the assembly is work part?The goal is to end up with the top level assembly file...
View ArticleClik here to view.
part not a valid version
So here's a fun situation; I'm cleaning up some older files. I set my load options as desired and when I open a particular assembly, one of the components gives me the message: So I try to use...
View ArticleClik here to view.
Motion simulation of multi-degree of freedom mechanism
Hello all, I have a mechanism shown in the following picture. Basically, it entails a fixed spring that holds the blue rod to be in contact with 4 fixed balls. Consider one pushes the red ball at the...
View ArticleMold Design
What is Technique to design Mold without using NX Mold Wizard ? I am not able to find all liberaries that required for mold. or from where i get all slider lifter , gate , runner and electrode liberaries?
View ArticleClik here to view.
How to make a groove on Circumference.
Hi allI am trying to make a groove on the circumfrence of the cylinder ,as shown in figure below but it is unable for me to do that. Any body who can do this plz share me the solution. For the ease i...
View ArticleClik here to view.
feature fails to update in time
I have a model with sophisticated parameter control. (Very sorry for no uploading due to company confidence!) A Combined Projection feature always fails to update correctly when a key expression value...
View ArticleClik here to view.
feature fails to update automatically
I have a model with sophisticated parameter control. (Very sorry for no uploading due to company confidence!) A Combined Projection feature always fails to update correctly when a key expression value...
View ArticleNX 12 MCD can't get OPC server
i try conncect nx to KEPServerEx ,nx display can't get OPC server,i try ,KEPServerEx is sucess conncect kepserver ex to plcsim,but nx can not get opc server
View ArticleClik here to view.
NX Machinery Library
Hello !!I’m using NX Machinery Library that I downloaded some years ago from NX website. I installed that library in HDD called D. I have actually installed NX 10 in HDD called C. Also I had NX9.0 but...
View ArticleClik here to view.
fail to extrude a trim curve
Simple job fails. Help would be appreciated. Fig.1 In SKETCH_000, the left arc is used as the boundary to extend the right arc.Fig.2 Trim Curce extends the right arc.Fig.3 The original right arc can be...
View ArticleClik here to view.
NX MCD automatic naming of Signals
Hi Guys, I am currently trying to configure an NX MCD Model that contains one element several times.It is a rather simple part that just has to move from one point to another so it's only using a...
View ArticleGM CREATING EGD&T - DESIGN RESPONSIBLE
I need to create a gm assembly Edg&t. Parts have been already uploaded to Teamcenter and approved by GM. Does anyone have any suggestions how to create an Edg&t assembly drawing? I know I...
View ArticleClik here to view.
add a conic branch tangent to a spline
I need to add a conic branch that is tangent to a spline. The result looks good, but zooming shows otherwise. Your help would be appreciated! Fig.1 The spline (red)....
View ArticleClik here to view.
NX Community Guidelines - Read Me First!
Here is what you need to know about using the NX Design Community 1) This forum is dedicated to all subjects pertaining to NX Design (CAD.) If you have questions related to simulation, manufacturing,...
View ArticleTitle Block Table Snap/Steps
Hi- I am trying to get my title block tables to align to one another. There are three tables in the attached image. I managed to snap them all to the bottom line. Then I selected vertical text...
View Article