Reverse Engineering
Good morning.I have a question about the NX reverse engineering software.We did know about a NX8 part named Imageware.What was its purpose?It's still used with NX11 - 12, or now must use an other...
View Articlechanging dimensions
Hi,When i want to change the dimensions of a feature i have to select Edit with Rollback or Edit Parameters to change the feature dimensions. When i want to change the sketch dimensions i have edit the...
View ArticleFatal error detected unable to continue. Unhandled operating system...
I was working with the program this morning, when suddenly the scroll zoom stopped working. I restarted the program and this error appeared on the screen. I could not solve it by looking at other...
View ArticleClik here to view.
associativeness of measured value
In my mind, the measuring tool for value input always gives associative results. In mose cases it works fine. But today I find that non-associative result is also possible. This makes me greatly...
View ArticleClik here to view.
Drawing automation
Hello, In order to speed up the drafting process, I was asked to implement further drafting automation. My study focussed on engineering however, so I haven't got as much experience with the whole...
View ArticleNeed in-depth details for NX Freeform 1 (Basic)
Greeting everyone! As the title says, I need details on Basic freeform (freeform 1) available in NX. Just a document listing all the features (list of commands, primarily surface commands) in Freeform...
View ArticleConfigure existing Checker
Hi, I'm new to Check-Mate and I'm trying to configure an existing checker to check if the part or drawing has an attribute already set. The one that I found that may be suitable for this is "Check...
View ArticleSOLID WORKS 2017 AP242 file TO NX 11
I have SW2017 files with PMI data, I was unable to import through AP242 translator. Reasons for failure may be1) SW2017 may not have the capbility of translating through AP242 (its is working in...
View ArticleClik here to view.
Adding Components to Assembly Looks Terrible
Hey, I was wondering if anyone can help me figure out why when I add components to an already made assembly, the new models look really bad. It's shown below in red, and looks like someone drew them....
View ArticleNX Routing Mechanical, Make Holes on Steelwork Stocks
Hi, I need to make some holes Normal to one of the four faces other than the two cap faces of a Hollow Square Beam created with Routing Mechanical and using the Steelwork Stocks. Issue is that when...
View ArticleClik here to view.
ERROR OPENING .PRT FILE
Hello everyone, One of my client is facing this issue. He's unable to open the part file and he's getting this erro. Any suggestions how to open and save back???
View ArticleHow to set the depth of the Section View ?
HelloHow to set the depth of the Section View ?I can modify the width be moving the arrows but how to modify the depth ? Is it possible ?
View ArticleClik here to view.
editing conic in sketch disrupts associativeness
I have a conic in the sketch "S1:Conic". When its Rho is changed from 0.5 to 0.4, an alerting message shows up. After exitting the Sketch Task Environment, a CSYS associated with it moves unexpectedly!...
View ArticleHow to draw environmental zones/areas for an Assembly
I am working as an Intern in a company and I have a STEP and a JT file of entire assembly of a airliner. My first task is to import this file into NX (which is easy). I need to have a big cube inside...
View ArticleAutomatically importing customer defaults
Hello everyone!Is it possible to automatically import customer defaults into NX somehow? I am interested in creating an installation batch file that would roll over some customization and that involves...
View ArticleCONVERSION: feature featureless, sketch non-sketch
1. I often convert a curve feature to a non-timestamp curve with Offset Curve (3D Axial, distance=0, associative disabled). Is it possible to reverse this conversion, e.g. converting a non-timestamp...
View ArticleClik here to view.
Revision block
Hi.. When I created the drawing templates for my company I used a temporary fix for the revision block. I marked the revision table as title block as well. It's a simple table with values we have to...
View ArticleNX Clearance Analysis Report
I performed clearance analysis to check the interferences in different parts of an assembly. The attached file shows the report in which we have the part number, type and the coordinates of the clash....
View ArticleAssembly constraint behavior
When trying to use the Distance constraint for assembling components together, the default value is something like "1763.3228" mm and it almost always tries to add the component in the wrong direction...
View Article"Component is Reference - only" hidden in drafting
Hi, I am using NX11 and TC 10. I have added few assemblies consisting of 100's of componentes in DRAWING specification, but when I am adding the BOM it is selecting all the parts from the navigatior. I...
View Article