Evaluating cross sectional areas of a hollow tube at distances along length?
I have a hollow tube with varying OD and ID throughout its entire length along axis X. Is there a way in NX for me to see the cross sectional area of the tube at specific increments along the X...
View ArticleClik here to view.
"Studio Surface" guidelines?
In a previous thread, made some very helpful comments on Studio Surface: The studio surface "will always attempt" to create an as simple and clean surface as possible. With this in mind, I try my best...
View ArticleSuppres message "new iray+ ray......"
Hi all, does anyone know if there is a setting the default hide the messages:"new iray+ ray traced studio rendering" This messages pops up when opening a old part in NX11 and higher. Is there a...
View ArticleClik here to view.
perplexing "Advanced Curve Fit"
I have a Combined Projection curve in the early stage of my model. To improve its quality, I enabled Advanced Curve Fit function. When I zoomed the model big in the later stage, I sadly found that...
View ArticleClik here to view.
T-shape with Welding Assistant
Hello everyone! Does Welding Assistant support this type of weld? I could not make it do this. Any ideas?
View ArticleDelay of 5 minutes to calculate an offset or a blend.
We are using NX11 in the company.I'm working on a part with a lot of blends and if I want to change a blend or do an "Offset Face", it takes aprox. 5 minutes until NX has calculate that it's possible...
View ArticleNX Stress Wizard - is it possible to edit mesh/loads/constraints without...
Hi, I have a simulation done with Stress Wizard. Is it possible to reopen it in Stress Wizard and edit (for example change the mesh size and force value)? I tried for quite a long time, and I can only...
View ArticleWhy do features affect surfaced faces?
Hello. Why does the surface face I created change geometry when I add an edge blend to my model and how do I prevent it from happening? I'm modeling vanes for an impeller. I created the vanes by using...
View ArticleCreating an eclipse on a rotated plane to see a perfect circle from the...
I am very new to NX12 and have a questionI have a series of points along 3d edges that i want to ROTATE to a plane so i can generate a 2d profileHow can I do this Thanks
View ArticleCreating an Assembly with Part Family as Components - Getting Error Part is...
Dear Forum, I am creating an assembly with components made from part families. When I replacement a component within the assembly with another part within the same part family NX is throwing an error...
View ArticleFreeing a hung license
Had a license get hung this morning, so the topic of how to free them up came them up. IT was aware of the command "lmutil lmremove -c 28000@LicServer NCFOUND Administrator tcuaets tcuaets0.0" But in...
View ArticleGeneration of drawing from developed sheet metal with coordinate points table
Hi everyoneI need to generate a detail drawings from a sheet metal assembly with a volute geometry (see image 1), and it is composed of various curved sheets and all the assy must be welded, my...
View ArticleThrough Curve mesh Continuity
Hello, I started to use NX recently, and I have a doubt about Through curve mesh continuity. I was designing a bottle and I used "Through Curve mesh" to create the body. When I make G1(tangent) in the...
View Articlebutton for cutomized model view?
Is it possible to create a button, e.g. on the top border bar, for a customized model view? Thanks!
View ArticleMirrored body and different mass
Often the following bug(?) occure: I made a mirrored body to 2d part and when I making weight calculation I see that Area,Volume and Mass characterisics are different between this two mirrored parts....
View ArticleClik here to view.
Copy feature expressions
I am trying to figure out a way to take Expressions from one feature and apply them to another without typing it in one by one. I constantly work with others who will use the hole or pocket command...
View ArticleClik here to view.
overconstraining in sketch-II
Since the previous thread, I often ran into troubles with constraining sketch. Very often quite some time wasspent on adjusting here and there without definite direction, and suddenly the issue was...
View ArticleHelp with creating a nest between two bodies.
Hello Everyone. I am a new NX user. Most experience is with the CAM side. Looking for a direction to go in for this problem. We are manufacturing small medical components. This requires a nesting...
View ArticleClik here to view.
Angular magnitude displacement selection does not exist in XY Result tool?
There was angular magnitude displacement selection in NX8 motion graphing tool. Graphing tool has replaced with XY result tool in newer NX versions. Angular magnitude displacement selection does not...
View ArticleNX MCD Capacitive sensor? Check material during simulation
Hi, I have a question about Siemens MCD V12. I have 2 blocks :- First block = PVC- Second block = aluminum. Those two blocks are on the same conveyor. I would like to separete them.I would like to...
View Article