Making Customer Defaults master over Preferences
I have read some discussions on this matter, but I've never found a clear answer. Is it possible to make the Customer Defaults (site) master over the in-part Preferences?I mean that all Preferences...
View ArticleSave Manager
I would like to share this post:https://community.plm.automation.siemens.com/t5/NX-Programming-Customization-Forum/Save-Manager-gift/m-p/454357#M10810
View ArticleSurface Book 2
Are any users running NX on a Surface Book 2? I saw a post about the Surface Book 1 and it seemed like the author of the post was impressed with the performance and had positive feedback on the...
View ArticleRadiation Absorptivity, Solar and Long-Wave
I do thermal/air multiphysics simulation and am not sure how to enter solar absorptivity. I found this radiation extinction property[1/mm] in the material properties and came to the conclusion...
View ArticleClocking Angle on Wire Harness Drawing
I'm new to NX Electrical Routing (and wire harness in general), so maybe there's an obvious answer I'm missing. I want to call out the clocking angle of connectors on drawings, but it seems when I...
View ArticleClik here to view.
matching curve details
I need to use Curve-A (blue) (on ZY) and Curve-B (green) (on ZX) to create a Combined curve (highlighted). Roughly, both Curve-A and Curve-B have two bumps and an infection range between the two bumps....
View ArticleClik here to view.
combined projection issue
"Side_View_(blue)": on ZY plane, both ends are tangent to Z axis"Front_View_(green)": on ZX plane"Combined_(grey)": from "Side_View" and "Front_View""Top_View_(purple)": projection of "Combined" on XY...
View ArticleHole series - Create solid (option:None)
Sorry if it's a repost. Can anyone explain why Hole Series doesn't have an option "None" like the other Holes have, which allowes creating of solids instead of subtracting them and also if it's...
View ArticleFaces to solid
Hello, I thought this topic has been discussed and re-discussed on here.. but i can't seem to find it. Please point me to another thread if it exists. I'm looking for a way to merge ~1500 faces which...
View ArticlePatterned Component, Finding Associated Component Pattern
Anyone know if there is a way to select a component(s) within an assembly, find out if they are placed by a Component Pattern, and then be able to select/find/identify which Component Pattern is...
View ArticleUp/Down/Left/Right for dragging or rotation?
Is it possible to use "Up/Down/Left/Right" keys to do dragging or rotation in NX? Since long I want to ask about this. Thanks!
View ArticleClik here to view.
sketch group constraint issue
As shown below, three connected lines (colinear) are packed into a sketch group with "Scalable Group constraint". It can be easily deduced that the sketch already is fully constrained. But the message...
View ArticleExtrude with turning
Hi everyone, Does anyone know, can I extrude a profile on the helix? I have complex profile with multiple loops and I can't do this with Surfacing :/ Best regards,Jack1
View ArticleSheet Metal Cut behavior
Hello, While in an assembly, I made a sheet metal part the working part and then made a Normal Cutout - and referenced some holes that were in the assembly. After finishing the cutout, I got a...
View ArticleNX 12.0.0 - Maintenance Pack 1 Announcement
Dear Siemens PLM Customer,NX 12.0.0 MP01 is an accumulation of fixes built for installation on top of the Windows 64-Bit image of NX 12.0.0.Note that this MP fixes the CAM issue (PR 9045206) discussed...
View ArticleSaving an NX file
Hi, I tried to post this in the proper disucssion board area but the "Start a discussion" button was not available. So I decided to post here. I'm going to run across a little scenario here and...
View ArticleClik here to view.
conic vs. spline
I'm thinking about the NX mechanism of building a spline. Below is a picture of Conic (left) vs. Spline (right). If they are mirrored, it can be find that they are completely equivalent. For the spline...
View ArticleDriving a deformable component from assembly level
Dear community I have found many examples of deformable part in the documentation and on tutorials.However it remains unclear to me how to use a deformable part not as a driving component (as seen in...
View ArticleClik here to view.
Placing a basic intersection symbol on a view ?
Hello ( Drafting Sheet metal )How to place a basic intersection symbol if the lines are wavy / irregular ? NX can't do it because NX wants straight lines.I can easily place intersection symbols if...
View ArticleClik here to view.
TCIN - Missing dialog options icon in the title bar
Hello,I have TCIN setup on my machine as Teamcenter - 11.2.0 and NX 11.0.2.7 MP4.For managed NX, dialog options icon is missing for 'Assembly Load Options' dialog, whereas for native NX it is...
View Article